Operator Aprimatic Electromechanical MATICBOX at 24 Vcc for residential use in spring doors and sectional doors, chain and belt drive. What. Equipped with an automatic path recognition system, deceleration in opening and closing phases and anti-crush sensitivity.

Motor gearbox Aprimatic Wave 400 to 230 V, use in individual residences up to 400 kg. What. Built on a sturdy aluminum monoblock injected and oven lacquered with special outdoor epoxy resin. It has a precise encoder that facilitates maximum control over the speed, strength and position of the door. Incorporates maneuver chart easy start-up with self-learning of the basic working parameters. Transmission consisting of endless steel screws and bronze crown obtaining a door movement soft, quiet and very reliable.

Motor gearbox Aprimatic Wave 600 to 230V, use in individual residences up to 600 Kg. What. Built on a sturdy aluminum monoblock injected and oven lacquered with special outdoor epoxy resin. It has a precise encoder which provides maximum control over the speed, force and position of the door. Incorporates maneuver chart easy start-up with self-learning of the basic working parameters. Transmission consisting of endless steel screws and bronze crown obtaining a door movement soft, quiet and very reliable.

KIT swinging motor Motorline LINCE for residential cancellations. What. Models of 230 Vc and 24 Vdc for running 300 mm, 400 mm, 600 mm

KIT engine EMFA MTCH of 800 N and 1000 N for residential-intensive sectional doors.

KIT engine Motorline SLIDE1024 to 24V with oil and grease lubricated reducer for sliding doors up to 1,000kg heavy duty and IP44 protection.

I'm going to go with the P-1. Designed for revolving doors up to 235 kg weight. What. Suitable for automating locks with side drive and gearbox.

Integrated electronic equipment that allows opening by key, button or remote control. Manual operation by crank.

The electromechanical actuator Erreka ARES is designed to drive automatic doors for use in the manufacture of motor vehicles.

Easy installation with two stem sizes (300mm and 400mm race), economic range, with obstacle detection and electronic soft shutdown.

Motor gearbox Forsa BOXER 230Vac up to 1000 kg oil bath for sliding doors of heavy use.

KIT 24V engine DEA model TEO 700 of 1000N, designed to drive other, of circular cross-section. What. It is the manufacturer's cheap and easy to install solution DEA.

Electromechanical drive Erreka ZETA of 24 Vdc for residential sectional doors For the purposes of this Regulation, the following definitions shall apply:

Electromechanical drive Erreka ZETA of 24 Vdc for residential sectional doors For the purposes of this Regulation, the following definitions shall apply:

The electromechanical actuator Erreka ARES is designed to drive automatic doors for use in the manufacture of motor vehicles.

Easy installation with two stem sizes (300mm and 400mm race), economic range, with obstacle detection and electronic soft shutdown.

Electromechanical engine Clemsa TO 300 for folding doors up to 3 metres in length per sheet, of semi-intensive residential use. 

Motor centre axle ACM of a kind used in motor vehicles, ideal for powering commercial doors or private garages.

The electro-brake brakes the blind once it's closed and avoiding opening it manually. The motor includes the auto brake unlock (black cable), to be able to activate the blind in case of lack of electric current in the room or garage.

Engine Clemsa AA30 electromechanical 230V for one-bladed swing doors for a maximum length of 3m by sheet. What. The AA30 model is ideal for automating residential doors for non-intensive use.

Motor centre axle ACM for use in the manufacture of products falling within heading 8528, ideal for powering commercial doors or private garages.

Do not allow the engine to lock when the door is stopped or left closed, if there is no electricity, you can climb by hand. It is recommended to use in places where there is NO alternative access to the shop/garage or an external brake unlocker cannot be installed, as when there is no electric current it can be operated manually.

Engine Clemsa AA40 electromechanical 230V for one-bladed swing doors for a maximum length of 4m per leaf. What. The AA40 model is ideal for automating residential doors for non-intensive use.

Engine FAAC model C721 with 24V operation for light residential and communal sliding doors of up to 800 kg.

KIT Sectional engine Pujol for sectional doors up to 10 m² /60Kg (STC-600) or doors up to 15m² /100Kg (STC-1000) is used. It has a chain-driven traction rail, soft stop, automatic closure and automatic obstacle detection.

24 V motor DEA model TEO 700 of 1000N, designed to drive other, of circular cross-section. What. It is the manufacturer's cheap and easy to install solution DEA.

Engine Erreka Sirius electromechanical 230Vac and 400Vac by chain transmission for hinged doors up to 50 m2.

Recommended installation in community and industrial doors.

Hydraulic operator Aprimatic TWENTY 270 for swinging canes one or two leaves, semi-intensive use. Speed deceleration closing. Built-in anti-crush safety valves. Quick emergency release. Useful length of stem 270 mm. Stem diameter is 16 mm.

Mechanical power supply for residential sliding doors up to 2.5 metres.

Engine Erreka Sirius electromechanical 230Vac and 400Vac by chain transmission for hinged doors up to 50 m2.

Recommended installation in community and industrial doors.

Kit Electromechanical motors Medva PW200 24V for swing doors for residential use up to 2.5 meters per sheet.

KIT Motor for sliding door Erreka PUMA INVERTER, at 230Vac for residential use up to 400 kg, with magnetic end run and obstacle detection.

Mechanical power supply for residential use swing doors leaves up to 3,5 metres.

Electromechanical engine Nice Toona HS, 24Vdc with magnetic encoder for rapid actuation of swing doors with blades up to 5 metres or 400 kg (TO5024HS) and up to 6 metres or 1,450 kg (TO6024HS). The installation of this motor is ideal for residential or community doors of intensive use.

KIT's engine Clemsa AA30 electromechanical 230V for one-bladed swing doors for a maximum length of 3m by sheet. What. The AA30 model is ideal for automating residential doors for non-intensive use.

Electromechanical motor of 24 V dc MEDVA PL500 for sliding doors of residential use up to 500 kg with built-in receiver box and 2 RollingCode controls.

Electromechanical engine Clemsa AA400 for swing doors up to 4 metres in length by leaf, designed for motorized residential use door. What. The model "AA400 424 B" allows us to perform a semi-intensive use motorization.

Electromechanical motor of 24 V dc MEDVA PL1000 for sliding doors of residential use up to 1000 kg with built-in receiver box and 2 RollingCode controls.

" THE PRODUCT HAS BEEN DISCONTINUED BY THE MANUFACTURER . WE RECOMMEND YOU CHECK OTHER ENGINES IN OUR SLIDING ENGINE CATEGORY "

Electromechanical gearbox engine 24 Vdc Nice TITAN HS with magnetic encoder for use in the manufacture of motor vehicles up to 3,7 m (TTN3724HS, TTN3724RHS), and for sheets of up to 6 m (TTN6024HRS, TTN6024HRS) AND.

I'm going to go with the P-1. Designed for roll-over doors up to 530 kg weight. What. Suitable for automating locks with side drive and gearbox.

Integrated electronic equipment that allows opening by key, button or remote control. Manual operation by crank.

" This product has been discontinued in 2024 and PUJOL has stopped manufacturing "

With the Lineal Low engine, it's no longer a problem to power a community door. With our reader system angle the automatism recognizes the position and function to be performed.

The Lineal Low incorporates an angle reader (encoding) which allows us to have no quotas in the case of vehicles with a maximum design speed exceeding 50 km/h, the maximum design speed shall not exceed 50 km/h.

Electromechanical engine BFT BOTTICELLI SMART BT A for intensive or very intensive use, designed to automate sectional garage doors.

It has a very compact design, suitable for installation anywhere, thanks to the wide range of chain rails available in various lengths.

The control centre and the end of run with encoder and mechanical cap are incorporated, respectively, on the operator and the guide.

Kit Electromechanical motors Medva PW230K 24V for swing doors for residential use for sheets up to 3,5 meters.

The PW230K engine is designed to power residential swing doors that we can give semi-intensive use.

Range of 24 V operators for heavy duty sliding doors with blades up to 1500 kg. What. Magnetic race terminals and command centers compatible with the U-link communication protocol.

Kit Electromechanical motor Medva PW230K 24V for residential use swing doors for sheets up to 3,5 meters.

The PW230K engine is designed to power residential swing doors that we can give semi-intensive use.

Electromechanical engine Forsa BAT 400 at 230 V for use with hinged doors residential up to 2,5 metres or 250 kg.

Kits Linear hydraulic motors Erreka VULCAN intensive use for double swing doors residential, community and industrial with a maximum leaf length of 4 or 6 metres depending on the chosen stem.

Kits Linear hydraulic motor Erreka VULCAN intensive use for swing doors residential, community and industrial with a maximum leaf length of 4 or 6 metres depending on the chosen stem.

Sliding engine oil bath traffic for sliding doors of industrial use and maximum weight other. 

Electromechanical engine Forsa SURF 300 for swing doors with sheets up to 3,5 metres and 300 kg of weight.

Motor kit CAME A5000A electromechanical 230V for one-bladed swinging blades up to 5 m, with a maximum weight of 400 kg.

KIT engine Pujol Marathon PRO Q II single phase for sliding doors up to 1000 kg residential, community or industrial. Equipped with electronic board and built-in receiver.

KIT Motor Came BK-1200 from 230V for sliding doors of up to 1200 kg and a length not exceeding 20 metres. What. It incorporates electronic card with programming display, built-in radio decoding and mechanical race endings.