Electromechanical engine NICE model TOONA 5external mounting for residential swing doors with blades up to 5 metres. Also available in 24Vdc version, with magnetic encoder.

Electromechanical motor NICE model TOONA 4 external mounting for residential swing doors with blades up to 3 metres. Also available in 24Vdc version, with magnetic encoder.

Engine FAAC S418 24V electromechanical for residential or communal high-voltage swing doors.

Accessory allowing 180° opening of an engine Motorline SUBWING.

Hydraulic motor Aprimatic FORTY 65 SP heavy use for hinged doors up to 6 metres in height. With installation of pump off the blade to prevent transmission of vibration the structure of the building.

Built-in anti-crush safety valves. Speed deceleration at the end of the route. 20mm diameter barrel and 270mm useful stroke.

KIT Hydraulic engine Aprimatic FORTY 65 SP heavy use for hinged doors up to 6 metres in height. With installation of pump off the blade to prevent transmission of vibration the structure of the building.

Built-in anti-crush safety valves. Speed deceleration at the end of the route. 20mm diameter barrel and 270mm useful stroke.

Engine buried and removable Nice M-Fab HS at 24 V for rapid operation of swing doors up to 3 m.

Buried and removable mounting, ideal for residential applications. Electromechanical motor gearbox 24 Vdc, with magnetic encoder.

Ideal for heavy use and fast manoeuvres: opening to 90° in approximately 8* seconds.

KIT engines Aprimatic R223 Irreversible electromechanical of 230 Vac for swing doors up to 2.5 metres per sheet, ideal for residential use.

Built on a sturdy injected and anodized aluminum chassis for outdoor use.

Hydraulic motor Aprimatic For the purposes of this Regulation, the following definitions shall apply:,ideal for powering community use doors with high vehicle traffic.

The hydraulic operator FORTY40BS for one- or two-bladed designed for continuous use with 100% working factor. What. It uses a 36 Vcc gearbox motor with «brushless» technology. It has an absolute linear encoder that allows an exact control of the position and speed of the door.

KIT Hydraulic engine Aprimatic For the purposes of this Regulation, the following definitions shall apply:, ideal for powering community use doors with high vehicle traffic.

The hydraulic operator FORTY40BS for one- or two-bladed designed for continuous use with 100% working factor. What. It uses a 36 Vcc gearbox motor with «brushless» technology. It has an absolute linear encoder that allows an exact control of the position and speed of the door.

Engine FAAC Reversible and irreversible version for community sliding doors for heavy use.

KIT Electromechanical engines V2 CALYPSO irreversible at 230 V for 2 residential swing doors for leaves up to 2,5 metres.

The KIT includes:: digital or analogue control panel for 2 motors at 230 V, with plug-in receiver and 2 bi-channel emitters at 433 MHz

KIT Engines buried Motorline "SUBWING' to automate swings up to 2.5 metres.

SUBWING has been developed to automate beating gates with blades up to 2.5m, available in 230Vac, or 24Vdc.

Discreet, it's buried beneath the base of the sheet, making it virtually invisible, without altering the appearance of the gate.

The construction of the outer case in galvanized steel provides great robustness and strength. With the possibility of applying mechanical caps on the automatic to limit opening and closing.

Electromechanical engine BFT "ATHOS AC A" Irreversible 230V for residential swivels up to 700 kg in weight and 4 metres in length.

Motor with articulated arm Erreka 230Vac cyclone for swing doors up to 3.5 meters and 250 kg per sheet, ideal for powering residential doors where we have small spaces or wide pillars.

24 V hydraulic motor BFT "FAST ULTRA BT A' for hinged doors of heavy use up to 5 metres in length. It incorporates a selectable locking system and magnetic run ends.

Full range of highly intensive use oleodynamic pistons, suitable for any type of application: residential, industrial or community.

KIT's articulated arm motors Erreka 230Vac cyclone for swing doors up to 3.5 meters and 250 kg per sheet, ideal for powering residential doors where we have small spaces or wide pillars.

Motor gearbox CAME ATS in 230V and 24V irreversible format for swinging canopies with a leaf length of up to 5 metres. ATS actuators are ideal for powering residential (230V) and semi-intensive (24V) community folding doors.

Kit Electromechanical articulated motor Medva PA250 of 24V for swing doors up to 2,50 meters per blade and 250 kg of weight.

The PA250 engines feature a built-in box-receiver, and are perfect for powering residential swing doors that feature wide pillars.

KIT 1 Electromechanical engine arm V2 CALYPSO irreversible at 230 V for residential sliding doors for sheets up to 2,5 m (CALYPSO400), 3 m (CALYPSO500), and 4 m (CALYPSO600).

The KIT includes:: digital control panel for 1 motor at 230V, with plug-in receiver and 2 bi-channel emitters at 433 MHz

BENINCA motor gearbox "BOB30" for residential doors up to 3 metres wide, quiet and quick to install, thanks to the 2 mechanical stoppers adjustable in opening and closing.

KIT Electromechanical engines DITEC PWR25H 24V for heavy use swing doors with a leaf length of up to 2.5 metres.

The irreversible actuator DITEC 24Vcc PWR25H is intended for frequent and intensive use. With machinery for making pulp of fibrous cellulosic material.

JAG engine of Motorline electrical engineer for use in the manufacture of products falling within heading 8528 [1] up to 4 metres/leaf (JAG400) and for doors up to 6 m/sheet (JAG600). Irreversible motor incorporating electric running ends in opening and closing.

KIT Electromechanical engines DITEC PWR35H 24V for heavy use swing doors with a leaf length of up to 3.5 metres.

The irreversible actuator DITEC The 24Vcc PWR35H is intended for frequent and heavy use. With machinery for making pulp of fibrous cellulosic material.

Hydraulic motor FAAC 422 for residential or communal sliding doors of 1.8 m to 3 m each.

KIT Electromechanical engines DITEC PWR25H 24V for two heavy duty swing doors with a leaf length of up to 2.5 metres.

The irreversible actuator DITEC 24Vcc PWR25H is intended for frequent and intensive use. With machinery for making pulp of fibrous cellulosic material.

Engine CAME In the case of vehicles of categories N1 and N2 with a maximum mass exceeding 2000 kg: designed to power swing doors up to 10 feet per blade.

Ideal solution for residential and community type enclosure installations.

Endless screw always protected by the dedicated cover.

KIT Electromechanical engines DITEC PWR25H 24V for two heavy duty swing doors with a leaf length of up to 3.5 metres.

The irreversible actuator DITEC The 24Vcc PWR35H is intended for frequent and heavy use. With machinery for making pulp of fibrous cellulosic material.

Electromechanical 230 V articulated arm motor Clemsa "AA 7002 B' with lock for residential overhangs up to 3 m per sheet.

Hydraulic motor EMFA Global Reversible and Irreversible community sliding doors intensive use with force regulation and smooth stopping.

Articulated motor BFT "VIRGO SMART BT A' residential hinged doors up to 2 metres or up to 200 kg. The main actuator incorporates a manoeuvre box with a 433 MHz receiver.

Residential electromechanical articulated-arm operator for swinging cantilever blades up to 2 m and up to 200 kg. Ideal for any installation requirement, allows you to easily solve problems related to large pillars thanks to the lever system. What. Control unit, control switch and mechanical stop blocks integrated in the operator.

KIT engine CAME In the case of vehicles of categories N1 and N2 with a maximum mass exceeding 2000 kg: designed to power swing doors up to 10 feet.

Ideal solution for residential and community type enclosure installations.

Endless screw always protected by the dedicated cover.

KIT Electromechanical engines DITEC PWR50 24V for heavy use swing doors with a leaf length of up to 5 metres.

The irreversible actuator DITEC The 24 Vcc PWR50 is intended for frequent and intensive use. With machinery for making pulp of fibrous cellulosic material.

Motor with articulated arm Nice "WALKY 1024' for residential swing doors of small dimensions up to 1,8 m.

It is particularly suitable for small wooden or PVC doors.

Irreversible electromechanical gearbox motor of 24 Vdc, with articulated arm.

Electromechanical actuator V2 STARK3 irreversible 230V or 24V format for sliding doors with blades up to 3 m ideal length for powering residential doors. Equipped with mechanical opening cap.

KIT available in electromechanical 230V with CITY4-EVO and electromechanical 24V with CITY2+.

Motor with articulated arm CAME "FAST 70' 230 V for residential columns. Designed to drive blades up to 2.3 meters and 200 kg in weight.

Electromechanical actuators V2 STARK3 irreversible 230V or 24V format for sliding doors with blades up to 3 m ideal length for powering residential doors. Equipped with mechanical opening cap.

KIT available in electromechanical 230V with CITY4-EVO and electromechanical 24V with CITY2+.

Articulated motor CAME "FAST 70' 24V for residential columns. Designed to drive blades up to 2.3 meters and 200 kg in weight.

KITs Electromechanical engines DITEC PWR50 24V for heavy duty double swing doors with a leaf length of up to 5 metres.

Reversible actuator DITEC The 24 Vcc PWR50 is intended for frequent and intensive use. With machinery for making pulp of fibrous cellulosic material.

Engine buried DEA GHOST 200 in 230V & 24V version for residential swing doors.

The buried automation for GHOST swing doors handles sheets up to 4 metres long and weighing up to 400kg. As the name suggests, this engine is invisible, performing its function underground with precision and maximum safety for people and media.

Engine FAAC 415 24V electromechanical for heavy-duty sliding doors designed for residential or community use.

Machinery for making pulp of fibrous cellulosic material V2 ZORUS 24V electromechanical for residential switchgear, designed to power canopies with wide pillars.

Two models are available:

• ZORUS2 for leaves up to 2,8 m per leaf.

• ZORUS4 for leaves up to 4.2 m per leaf.

Electromechanical engine CAME ATI A5124 24V for swing doors up to 5 metres per leaf.

Machinery for making pulp of fibrous cellulosic material Nice "WALKYKIT 2024' for residential swing doors of small dimensions up to 1,8 m per sheet.

It is particularly suitable for small wooden or PVC doors.

Irreversible electromechanical gearbox motor of 24 Vdc, with articulated arm.

DMIL HURACAN 35 engine for swing doors up to 2,5 metres by sheet with built-in running ends.