List of products by brand Nice

Pair of transmission axes 20x20 mm, length 1500 mm for tilting motor Nice Ten.

Motor support Nice Ten in length 520 mm.

In the case of vehicles of categories M1 and N2 with a maximum mass not exceeding 2000 kg:

Replacement plant Nice SNA2 for SPINBUS SN6021 sectional engines.

KIT Motor NICE model SPINKIT 650N for sectional doors up to 8,8m2 and tilting doors up to 9,8m2. What. Leash traction.

The version in KIT comes with pre-assembled guide of 3m SPIN11KCE.

THE NICE SPIN ENGINE HAS BEEN REPLACED BY THE NEW MODEL NICE SPIDO600 WITH IMPROVEMENTS OVER THIS MODEL

1 channel module for the operation of 1 automatic with step-by-step function (Open-Stop-Closure).

Metal wrapping for photocell Nice FT210.

Table of manoeuvres Nice OGA2N at 24V for SHEL50KCE, SHEL60KCE and SHEL75KCE sectional motor. What. The plate has a built-in receiver at a frequency of 433.92 MHz and functions of automatic shutdown, motion regulation and reversal of motion in case of obstacles during travel.

Unlock with motor key Nice for buried engine L-Fab or M-Fab.

Unlock with a lever key, which will be used in case of installation on surfaces, such as sand or ground.

Compatible with engines Nice M-Fab, L-Fab and Big-Fab.

NICE ROA37 manoeuvre chart for sliding engine THOR 1500, incorporating a receiver with RollingCode 433,92 MHzcompatible with FLOR and SMILO emitters. The programming is analog using micro dip switches.

Spare center Nice SPRBA3HSR10 for RB250HS and RB500HS sliding engine.

Gearbox and pinion Nice ROBUS and ROAD.

Manage the opening of your residential garage door with NIC's IT4WIFI WiFi moduleIt is available as standard on iPhones and available on Google Play for Android devices. The NICE IT4WIFI module is operated by Opera, only available on NICE manoeuvring frames.

Security photocell with mirror model Era Photocell M 12/24v for distances up to 15 metres.

Emitter with mirror. Orientation and sensitivity regulator. The output of the relay shall be 500 mA / 48 V

This is the NICE RUA1. Control electronic plate RUN 1800 / RUN 2500 for sliding motors of automatic doors and entry gates weighing up to 1800 kg and 2500 kg in its two versions with this model of control manoeuvring box for a totally safe and efficient configuration of its functions thanks to this control centre

Replacement towing vehicle Nice SHEL50 AND SHEL75.

Manufacture from materials of any heading Nice TOO3000 and TOO4500 230 V electromechanical switchgearblades up to 3 m and 300 kg (TOO3000 model) and up to 4,5 m and 250 kg (TOO4500 model).

Motor housing Nice SHEL50 and SHEL75

NICE swing arm with sliding bearings and optimised geometry for overflowing swing doors.

Electronic plate Nice SPA600 for SPIDO600 sectional motor

Replacement electronic plate Nice OTHER for the engine THEFT 300.

Accessory Nice BMA1 for openings up to 360° in engines buried for leaves with a long maximum of 3.5 m.

Central command Nice Moonclever MC424L for 24 Vdc sliding door motors, without encoder, with integrated receiveror and ready for Opera and Solemyo system.

Pair of transmission shafts 20x20 mm, length 200 mm for tilting motor Nice TRY.

Pair of standard telescopic straight arms for tilting motor Nice TRY.

Transmission device for a couple of motor shafts Nice TRY.

NICE Era One LR bidirectional long range 433 MHz with 4 buttons: 3 radio channels and 1 button to request automatic status.

NICE transmitters were One BD bidirectional of a kind used in motor vehicles: 3 radio channels and 1 button to request automatic status.

Radio frequency 433,92 MHz with rollingcode encoding, enabling code management, self-learning with 192 Bit encoding, also compatible with encoded receivers Nice O-code floor. The two-way Era One remote is compatible with previous versions of plug-in and external receivers Nice, operating in one-way mode.

KIT engines Nice WINGO 24V electromechanical for two-bladed swing doors up to 2 m per sheet (model 4024) and up to 3,5 m per sheet (model 5024).

Replacement plant for Nice TN2030L and TNLKCE.

Electronic plate Nice RBA2/A (SPRBA2) for ROBUS 350 sliding engine.

Unlocking kit Nice KI1 from the outside with metal rope and key chain.

Module for the operation of 2 open-stop-close automatic systems in single or multi-group mode.

Module for the operation of 1 automatic open-stop-close in single or multi-group mode.

Other, of circular cross-section Nice IN ORDER TO ENSURE THE CORRECT APPLICATION OF THIS REGULATION, MEMBER STATES SHALL TAKE INTO ACCOUNT THE FOLLOWING:.

Table of manoeuvres Nice OGA0 to 24V for SHEL50KCE, SHEL60KCE and SHEL75KCE sectional motor. What. The plate has a built-in receiver at a frequency of 433.92 MHz and functions of automatic shutdown, motion regulation and reversal of motion in case of obstacles during travel.

Central or maneuvering frame Nice SOON reference SPSOA2R10 compatible with the former central Nice SOA2.

Unlocking Nice WINGO thumping engines.

Table of manoeuvres Nice SP081-B control center electronic card A824.

Control, programming and diagnostics unit for equipment with the BUS T4 connection, in situ or remotely via GPRS through the connection with your PDA, Smartphone or PC.

Central Nice WLA1 for WALKY articulated motor WL1024C.

Guidance for the extension of 0.8m + motor belt Nice SPIDO 600, PLEASE.

ROX is an electromechanical gearbox motor for the automation of sliding doors up to 600 kg for residential use: has an electronic control unit incorporating a 433,92 MHz radio receiver with coding FLO, FLOR, OPERA, HCS SMILO.

ATTENTION: THE NICE ROX600 ENGINE HAS BEEN DISCONTINUED FOR THE BETTER PERFORMANCE ROBO600 MODEL. WE HAVE THE ROBBERY KIT IS 600.

NICE A01 manoeuvring chart of 230 Vac, for single-phase motors with retractable doors, not automatically closed. It incorporates a RollingCode 433.92 MHz receiver for the Flo, FloR and Smilo transmitters.

BOX NICE A01 HAS BEEN REPLACED BY THE NEW MODEL MC200, CLICK HERE TO SEE IT.

MC200 is an electronics switchboard enabling the control and operation of a motor for the automation of a blind, or a sliding door, or a sectional door, or a curtain, or other similar applications.

Compatible with the IT4WIFI module to be able to open and close via a mobile device (Android or iOS) thanks to the built-in WiFi connectivity.

Table of manoeuvres Nice MC800 for 230 V swing door motors with BlueBUS technology and Opera system.

With technology Nice BlueBUS, compatible with the Opera system, for the management, programming and diagnosis of automation, also remotely.

Compatible with the Opera system which, through the O-View multifunction screen, allows you to customize the system by modifying the opening and closing positions, the leaf gaps and decelerations, changing for each motor parameters such as, for example, force, speed, sensitivity to obstacles.

Painting Nice D-Pro 500 for single-phase 230V or three-phase 400V motors with mechanical and electronic running ends.