List of products by brand V2

Synchronous and steerable wall photocells (180o) V2 Sensitive-WL with battery powered transmitter.

Issuer V2 electronic equipment model PHOX-4 with RollingCode coding system at 433,92 MHz for receivers V2 with standard code.

Fast coupling clutch V2 In the case of engines with a rated torque of not more than 20 Nm (for LEX, LEX-RM, LEX-FE, LEX-RFE).

Issuers V2 LOKI Tube engines for domestic blinds and awnings.

Issuers V2 PROTEO for tubular motors for domestic blinds and awnings.

Cable-based signal anemometer V2 MISTRAL for automatic tubular blinds or awnings.

Anemometer with sun and temperature sensor V2 Signal hurricane by cable, for tubular blinds and awnings.

Anemometer with sun and temperature sensor V2 Hurricane-RS radio signal, for tubular blinds and awnings.

Anemometer with sun and temperature sensor V2 TYPHOON rADIO signal and powered by solar cells, for tubular blinds and awnings.

Vibration anemometric sensor, whether or not combined with other instruments V2 SYROCO-RS, system by radio (434.15 MHz).

Electromechanical engine V2 In the case of ATRIS 24V of a kind used in motor vehicles up to 15m2, with a starting force of 1000 N (100 kg)

Other, of circular cross-section V2 AGON for revolving doors with 76 axles and up to 360 kg with electro-brake. What. Motor for spring-loaded industrial revolving doors, shaft 76 mm in diameter, lifting capacity up to 360 kg and crown 240.

Trailer and connecting motor chain sectional V2 ATRIS.

Set supports and magnets sliding motor V2 YROS.

Unlock key V2 It's called Calypso.

Unlock key V2 It's called Calypso.

Table of manoeuvres V2 AYROSS PD19 230V plate, ideal for use as a spare in the AYROSS sliding motor.

The programming of parameters and configurations is done via the digital screen. The dashboard incorporates NO receiver, but is compatible with MR2 plug-in receivers.

Table of manoeuvres V2 CITY5 230V digital for the management of a traffic light installed near a vehicle crossing with a two-way direction of travel.

Read end run magnetic motor slide V2 ALFARIS (1 piece).

Transformer motor sliding V2 TORQ500D 24V 300W.

In the case of vehicles of categories M1 and N2 for a single leaf and for running ones.

Digital control panel 230V with encoder V2 CITY1-EVO for one- or two-leaf clover and slippers.

Table of manoeuvres V2 CITY9 an analogue 230 V for sliding doors.

" TABLE CITY9 HAS BEEN REPLACED BY NEW FLEXY2 MODEL FULLY COMPATIBLE "

Digital manoeuvring chart V2 CITY2+ 230 V for sliding doors and doors equipped with two 24 V direct current motors.

Analogue maneuvering chart V2 CITY11 230 V for swing lamps (one and two sheets).

Table of manoeuvres V2 EASY-LUX for rolling shutters with courtesy led light and buttons.

Table of manoeuvres V2 EASY-BASIC an analogue 230V with built-in receiver for roller shutters.

Table of manoeuvres V2 EASY1 230V analogue for blinds, blinds and awnings with built-in receiver 433.92 MHz.

Table of manoeuvres V2 EASY2 230V analogue for roller blinds with courtesy light and automatic closure.

Table of manoeuvres V2 "FLEXY' analogue 230V for sliding and swinging doors.

Replacement of sectional motor chain tensor V2 THE JEDI.

Electronic plate "PD14" for use as spare parts in sliding motors V2 OTHER IT 'S 24V .

The PD14 is equipped with a display that allows, in addition to easy programming, the constant visualization of the status of the entries; in addition, the structure with menus allows a simple programming of working times and operating logic.

Other, of circular cross-section V2 AGON for revolving doors with axle 60 and up to 280 kg with electro-brake. What. Motor for spring-loaded industrial revolving doors, axle 60 mm in diameter, lifting capacity up to 280 kg and crown 200/220.

Inverter board V2 I'M NOT SURE.

End-of-race supports or blades V2 ALFARISS, PLEASE.

Head Electric motor V2 AZIMUTH irreversible for sectional and tilting doors up to 8 m2.Starting force 500 N 50 kilos .

Engine V2 Electromechanical JEDI 24 V irreversible for sectional and tilting doors up to 15 m2 with a starting force of 1000 N (100 kg).

" THE JEDI MODEL HAS BEEN DISCONTINUED AND REPLACED BY THE MODEL ATRIS "

KIT engine V2 Electromechanical JEDI 24 V irreversible for sectional and tilting doors up to 15 m2 with a starting force of 1000 N (100 kg).

" THE JEDI MODEL HAS BEEN DISCONTINUED AND REPLACED BY THE MODEL KIT ATRIS "

Electric motor kit V2 OTHER for use in the manufacture of motor vehicles residential buildings up to 9 m2.

Hydraulic motor V2 URSUS 230V for heavy duty swing doors, sheets up to 4 or 6 meters long designed to power canopies of community garages.

Electromechanical engine V2 STARK6 irreversible in 230V and 24V format for swing doors with blades up to 6m. Designed to power residential or small semi-intensive community doors.

Electric motor kit V2 STARK6 irreversible in 230V and 24V format for swing doors with blades up to 6m. Designed to power residential or small semi-intensive community doors.

KIT Electromechanical engine V2 "ATRIS 1000' Irreversible 24 V for sectional and tilting doors of up to 15m2, with a starting force of 1000 N (100 kg).

Electromechanical engine V2 New Zealand 24V for residential canopies up to 2 m per sheet, equipped with a mechanical opening cap.

Kit Electromechanical engines V2 24V NYK for residential lights up to 2 m per sheet, equipped with a mechanical opening cap.

Electromechanical actuator V2 STARK3 irreversible 230V or 24V format for sliding doors with blades up to 3 m ideal length for powering residential doors. Equipped with mechanical opening cap.

Electromechanical actuator V2 STARK3 irreversible 230V or 24V format for sliding doors with blades up to 3 m ideal length for powering residential doors. Equipped with mechanical opening cap.

KIT available in electromechanical 230V with CITY4-EVO and electromechanical 24V with CITY2+.

KIT Electromechanical engine V2 "ATRIS 700' Irreversible 24 V other, of circular cross-section, of iron or steel, with a starting force of 700 N (70 kg).